Blog Layout
Deer Hunting Basics
Mar 19, 2015
Deer Hunting Basics
Part I
The very first thing one should consider when hunting is safety. Before you even think about going into the woods, consider taking a hunters safety course from your local wildlife agency. And even if you are just scouting your hunting area, you should take some basics with you. ~A flashlight
(be sure the batteries are fresh and the flashlight is in good working order) ~A compass, matches or lighter (These will come in very handy should you get lost in the forest. A good portable GPS system is handy too.) ~A good first-aid
kit (It should include bandages, snake bite kit, turn-a-kit, antiseptic, etc)
Deer are usually more active around dawn and dusk and tend to sleep in the middle of the day and late at night. This is thought to enable the digestion process and be a defense against predators which are less active during these times. Venison do feed during mid-day sometimes, but this is a quirk that not likely to be repeated by that deer often.
Before hunting season begins, right after the bucks have rubbed the velvet from their antlers, scout the woods which you are going to hunt. Look for food sources and signs of deer such as tracks, bedding areas and funnels. A buck won't rub the larger tree and brush except during the rut. He will, however leave signs of himself by rubbing his antler velvet on smaller trees and bushes in the forest.
Start scouting your hunting area in early to mid-summer. Be careful and disturb as little of the hunting grounds as possible. Try to make very little noise. Also try not to leave any human scent. Prepare for scouting the forest the same as you would for hunting in the same woods. Keep in mind though that over scouting can have a very bad effect on the wildlife, and push the game out of the hunting area, or make the animals nocturnal. Search for area where oak trees have a large number of acorns that will shed in the coming fall. Set your tree stands and blinds near these areas before the acorns ripen and the deer start feeding on them. Then leave the area alone until the hunt.
Venison has three goals in life, eat, sleep, and mate. Try to find hunting areas where the ground is covered in greens such as clover or rye grass and other tender plants. Look for trail routes, scrapes, and tracks around the surrounding areas.
Dear sleep in places where the brush and other cover is very thick. These areas are difficult to hunt because the cover limits ones vision, and the noise a hunter would make getting to his or her stand or blind would quickly alert deer to his or her presence.
The rut is the time when the deer mate. A buck is much more active a larger amount of time while he searches for mates. And his senses are dulled during the rut. This gives a hunter a slight advantage over the venison. A hunter is more likely to get a buck in his sights during the rut for the above reasons.
Redneck Know How Blog
Will the HYCHIKA cordless screwdriver help me get the screws screwed when my arthritis is acting up? Sometimes it's painful to keep twisting a manual screwdriver and hopefully this is the solution. Come see how things turned out.
I was asked by Hyper Echo to try out their 20 volt cordless string trimmer and edger and do a review on it it. I did and in this article I will let you know what I found out.
Every fisherman has his or her own favorite techniques to catch this beloved fish. Why is crappie, (or pomoxis, if you want to get scientific), are so beloved? Well, they give one heck of a fight when caught. A 2 lb. crappie can put up a fight to rival a bass of larger size. So catching them is fun. There is also the taste factor. Fried crappie tastes great.
The weather is warm and folks are crappie fishing. Here’s a fried crappie cake recipe that I enjoy. You can eat them plain with some fried taters, or slide them in a bun with some tarter sauce.
I was asked to review the .SORAKO 800-3000SPM Jigsaw And after the pleasant experience with the SORAKO chainsaw, I was happy to give their jigsaw a try. Come find out what the results were.
I was given the opportunity by HYCHIKA to try out and review their SORAKO chainsaw. This blog describes what I think about the chainsaw. How well I like it as well as my experience in using it.
I was aske to review the Hychika cordless power drill and I did. I used it to do various things in my home and in my wood shop. This is what I think of it.
Everybody seems to be in love with dovetails these days. Myself included. They look nice, feel nice, and they make the woodworker feel an overwhelming since of pride when he makes tight and even. Especially the hand cut dovetails. Dovetail joints can be produced with power tools. And there are dovetail jigs you can buy and make. It makes getting precise dovetails with no gaps a lot easier. But nothing feels more satisfying than finally getting hand cut dovetails tight and gap free. And for the record, I use the term, “gap free”, very loosely. I’d wager that even the best woodworker gets gaps in their dovetails no matter how hard they try. Maybe not as many as us new to middlin’ woodworkers, and certainly not as noticeable, but there are gaps in their dovetails. Nowadays, people use dovetails not only as a joint, but as decoration. A showpiece if you will to show off the craftsmanship of the woodworker. But the reality is that they were not originally meant to be pretty. They were utilized to hold pieces that were heavily used together. Such as drawers or other parts of furniture and other items that were constantly pulled or tugged on. In the example below, you can see how the angles of the dovetails will keep the joint from coming apart during the tugging of the drawer when opening it. This part of the joint is where the dovetail joint get’s it’s name. Often when used on boxes, the orientation of those angles are switched around, placing them on the front of the box as a decoration, and the pins of the joint is put on the side. Great for looks, not so great for function. Of course for most smaller boxes, the function of the dovetail really isn’t needed and using dovetails for looks is fine and an anesthetically pleasing way to show off craftsmanship. But let’s not give up on using the dovetail joint for utilitarian purposes when building boxes too quickly. They can be a great way to join a bottom to a box that will be holding heavier stuff, such as tool boxes. The angle of the dovetails can manage the stresses of carrying heavier items such as tools if you wish to maintain a *NO screws or nails* policy on your woodworking projects. Or you can use the dovetail joint along with screws for extra protection against the bottom dropping out. So the purpose of the dovetail is a lot more than to just make your woodworking look good. In fact, long ago, they were hidden. Simply a way to join parts and give them the strength to do what the item was meant to do, and be hidden when the drawer was closed. Using the dovetail joint for decoration is a modern thing. Which I have nothing against. I love to show off dovetails I’ve made nearly perfect. Well, in my eyes anyway. Roy Underhill and Paul Sellers would likely just look at them and grin, maybe chuckle at me being so proud of something so far from the skill level they have achieved.
My wonderful experience with Starbond Super glue is explained in this blog post. The absolute best CA glue I've used.
An option for dealing with nail holes and voids in a table top made with pallet wood.